Toilet Tips for Maintenance
According to the Main Component Life Expectancy Study prepared in 2007 by the National Association of Home Builders (NAHB), “Toilets have a limited lifespan, but the components inside the toilet tank do require some maintenance.” so you should pay attention to the components inside the toilet tank.
Components, Toilet plumbing fixture models now typically two pieces (tank and bowl) are made from vitreous china. Mechanical components, which is located in the tank, work together as a system to perform gravity flush. A common type of assembly is known as the flush valve flapper design. As the diagram below illustrates, the components include:
1. buoy
2. Fill valve
3. Arm lift
4. Tank fill tube
5. Bowl fill tube
6. Flush valve flapper
7. overflow
8. Flush handles
9. chain
10 Water Levels
11. Filling valve shaft
12.Tabung flush.
When initiated by the flip handle, assembly parts act together to force the water out of the tank, through the flush tube, and go into the bowl, flushing the contents through a siphon and the drain. This is a simple mechanical assemblies, and not at all difficult to clean and maintain, as long as you do it regularly.
Cleaning, Vitreous china has a shiny appearance that is available in various colors. strong materials, care should be taken not to attack the surface or roughly handle the connection, because the vitreous china can scratch, chip, and even crack. Clean the inside of the toilet bowl should be done at least once a week. Using a brush, and toilet bowl cleaners or household bleach, the inside of the bowl should be scrubbed thoroughly. Be sure to not use abrasive cleaners because it will make the glow becomes less / be blurred from time to time. You also have to disinfect the toilet, seat, lid, tank, and handle surfaces with disinfectant spray throughout the week. This is a good idea to keep the area around the toilet, and on top of the tank, free of each item. This will ensure your ability to easily find the water turn off valve if needed in an emergency, and easier for you to open the tank lid to check on the tank and make necessary adjustments or repairs.
Leakage, while you clean the toilet, you also check if there are all signs of external leaks along the floor, and around the tank and bowl. If leaks are present outside the tank, make necessary repairs. The bowl is joined to the floor flange with a wax ring or gasket used to seal the connection and prevent leakage of waste and odor. Over time, the wax ring can be damaged and allow seepage occurs around the base of the toilet. Depending on the use of the toilet, you may wish to replace the wax ring every 5 to 10 years, although in some cases they can last much longer. It is important for the floor and under the structure that the type of leaks repaired promptly and immediately replaced the wax ring.
Toilets should not move, it must be installed tightly and firmly into the floor. If you detect a wobble occurs, seek what is causing the problem. This is probably a nut loose floor, or the toilet may be properly seated on the wax ring. Whatever the cause, you must make the necessary adjustments and ensure that the toilet securely bound. Check the condition of the caulk around the base of the toilet bowl where it meets the floor. Caulk should be in good condition and adequate seal seam. If necessary, remove any deteriorated caulk and apply new caulk around the bottom edge of the toilet.
Toilet Tips for Maintenance
Other Common Problems, From time to time the toilet you may experience various kinds of operating problems, such as running an internal water leak, clogged drains, flushes slow, or damaged components. If you experience a clogged drain, you may want to consider what is causing the clog. To ensure that the toilet, drain, and sewer pipe to function as expected, it is good practice not to flush foreign objects down the drain. Clogs can be removed using a number of techniques or methods. Clogs are most often removed by using a toilet plunger or a wire hanger, or snaking through the obstruction in the drainage. Other methods may be needed depending on the circumstances that caused the strike.
If the toilet slow to flush, the water stored in the tank can not fill to the appropriate level, or holes located beneath the lip flush toilet may be clogged. Open the lid of the tank and determine if the water level is located near or just below the overflow pipe. If too low, the float may not work well to allow water to enter the tank. If the water level in the tank seems to fit, you’ll want to check the hole and rinse clean buildup that restricts the flow of water. Using an inspection mirror and hanger wire, hole probe rinse to remove surface buildup. While the dam hole rinse and add the lime remover to drain the overflow in the tank. This will lead to the pit of lime remover rinse and dissolve mineral buildup. Remove the dam in the hole and rinse off after 8-12 hours are used as usual.
If you hear water running in the toilet that no one uses, to be sure you are wasting money, and is it really worth it to you. If you suspect that there is an internal leak but can not hear the water running, add liquid a little food coloring into the dark water stored in the tank. If after 15-30 minutes you see the same color dye in the bowl even if you do not flush the toilet, so you know there is water leaking from the tank into the bowl. Water is the internal leakage is usually caused by mechanical components inside the tank that needs adjustment, or damaged or deteriorate. This component is available at your local hardware or home improvement store and easy to replace. Keep in mind that before doing any type of job in the toilet, make sure you turn off the water supply valve, located near the toilet.
After reading about maintenance tips will keep your toilet clean and functioning properly for years to come.
Toilet Tips for Maintenance by Buildipedia Staff
